Frequently bought together
Description
- Hands-Free Setup
- Backlit Display
- Relative Zeroing
- USB Rechargeable
- Shock Resistant
A crooked bubble vial in a dark corner leaves you guessing. The Snap & Read Digital Angle Gauge holds to steel on any of its four sides and shows the angle in backlit digits, so both hands stay on the work. Zero it on a sloped surface and it reads every bevel from there.
Both Hands Free
The Snap & Read Digital Angle Gauge holds itself in place on steel, so you stop juggling the level, the light and the pencil. Magnets are built into all four sides of the 60 x 60 x 30 mm, 2.36 x 2.36 x 1.18 inch cube, which means any face can go against the work: flat on a cast iron saw table, upright against a blade, or tucked under a run of EMT conduit. The whole body weighs 159 g, 5.6 oz, a light load for the magnets to carry when you set it on a vertical pipe or a machine frame. When you bend conduit or fit tube, the reading stays where you put it while you adjust the bender or tack the joint. You set it once, step back and read the number.
Clear in the Dark
Dim crawlspaces and dusty basements are where a bubble vial turns into guesswork. On the Snap & Read Digital Angle Gauge, the angle appears as numbers on a backlit digital screen, lit in bright green, so you read a figure instead of judging a bubble between two faint lines. The screen sits on the front face of the cube, which matters when the gauge is held to ductwork above your head or to a condensing unit housing at floor level. A hold function freezes the reading, so you can pull the gauge off an awkward spot and read it in better light. For HVAC work under the house or overhead in the rafters, the number is there the moment you look. No squinting. No second guess.
Angles Without Arithmetic
A bench that sits a degree off level throws every bevel you measure against true level off by that same degree. Press the dedicated zero button and the Snap & Read Digital Angle Gauge takes the surface it sits on as its new 0.00° reference, then reads every angle relative to it. Switch back to absolute mode when you need true level for a cabinet run or a shelf. Set the cube on your table saw top, zero it, then place it against the tilted blade: the screen shows the bevel itself, with no offset to add or subtract in your head. A short press powers it on, a long press powers it off, and zeroing has its own dedicated button. You make the cut on expensive hardwood knowing the number came from the saw, not from your math.
Charged and Ready
Coin cells always seem to die halfway through a setup. The Snap & Read Digital Angle Gauge runs on a built-in rechargeable battery that you top up over USB, from a wall adapter, a laptop or a power bank in the truck. To save that charge, the gauge switches itself off after 3 minutes, so a cube left on the bench or dropped into a pocket doesn't sit draining overnight. That matters if you calibrate a miter gauge at the start of a project and leave the cube in a drawer until the next one, or keep it in a tool bag between service calls. Charge it alongside your phone, and the battery aisle drops off your shopping list for good.
Built for the Jobsite
Tools that live in an apron pocket hit the floor sooner or later. The housing of the Snap & Read Digital Angle Gauge is molded from shock-resistant ABS, a high-impact plastic designed to absorb knocks from daily handling in a workshop, on a construction site or outdoors. The sensor and battery sit inside that shell, and the compact cube shape keeps it small enough to ride in a pocket instead of balancing loose on a ladder top. After any hard drop, set the cube on a surface you know is level and check the reading before you trust it on the next cut, the same habit you would keep with any precision instrument. Toss it in the bag with your chisels and squares. It is built to come back out ready to read.
Technical characteristics:
Dimensions: 60 x 60 x 30 mm | 2.36 x 2.36 x 1.18 inch
Weight: 159 g | 5.6 oz
Measuring range: 4 x 90°
Display: Backlit digital display, green backlight
Measuring modes: Absolute zero, relative zero
Reading hold: Yes
Controls: Short press power on, long press power off, dedicated zero button
Product content:
1x Snap & Read Digital Angle Gauge
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Not Happy with your purchase? We take it back!
Your satisfaction is our top priority
Item covered by the Purchase Protection Program
Shop on Ozerty with confidence, knowing that we're here to support you if any issues arise
Our delivery guarantee
- Shipping 72h
- Tracked parcel
- Packed with care
- 5£ credit in case of any delay!
Any Questions?
Our support team answers you 9:00am to 6:00pm Monday to Friday:
contact.uk@ozerty.com
We found other products you might like!
